Elektral ThruScan Manual de usuario descargar pdf (Pagina 53)

10.2.1 ThruScan

s3/

s6/s9 SRC-SCADA Remote Control Program User Manual

Please enter your Registration Code for the activation of your SRC-SCADA Remote Control Programmer. You

can have your Registration Code from your dealer by e-mail or telephone.

1.1- Language - Select your language from “Setting” window.(English, German, Spanish, Turkish)

1.2- Connection – To work with a metal detector you need to connect it to a serial port via the cable. To make the

program, please make sure what port you are using, select the "Com Port" and choose COM1 to COM4. If the

communication is performed by Telephone Lines then the com-port of the modem should be selected

visually. You can check several ports simultaneously for the right communication.

1.3- If the communication would be done by telephone lines; then the phone number should be entered to “ Phone

Number” window and pressed “Dial”. There is no difference between local (in house), domestic or international

communications.

1.4- Selection of GATE NO - You have to give index number for each walk-throughs from 1 to 16.

(Note: All ThruScan s3/s6/s9 number-1 at the factory out-put)

(Note: During organising the network; When you communicate with selected ThruScan s3/s6/s9, you should

disconnect the other Magnetic Walk-Thru Metal Detectors from your network ! )

To change the ThruScan

s3/s6/

s9’s index number: (Only one ThruScan s3/s6/s9 has to be connected to the

network)

a) Arrange the communication. (Select right COM port)

b) Press “STOP” button,

c) Write “NEW”(Caps Letters!) to “IN COUNT” window,

d) Write the index number(1-16) you want to assign to that ThruScan s3/s6/s9to “OUT COUNT” window,

e) Pres to “IN COUNT” button,

You can repeat this process with the other Magnetic Walk-Thru Metal Detectors under communication to assign

your own index number.

1.5- Select the Magnetic ThruScan ’s number from “GATE NO” window. This will up-date the complete information on

your SCADA screen at your pc for the data of the selected walk-thru.

“STATUS” window will display not only your executions such as, RUN(X), STOP, READ ERROR, IR(INFRARED)

ERROR, LOW BATTERY etc.. i.e. the error codes (Telephone line disconnection displayed as READ ERROR) but also

the walk-thru’ errors are displayed.

1.6- In “Level Select” window; 10 security levels are existing of which NC (NILECJ) can not be changed. The other 9

can be assigned to the desired sensitivity. You can also change several Security Levels simultaneously and send

together to your ThruScan s3/s6/s9.

To change the Security Level Adjustments:

a) Press “STOP” button,

b) Set the Security Level you want to change its sensitivity at a value between 0-245 ( 0- the most sensitive ,

245- the less sensitive)

c) “Send” it or them to your Magnetic Walk-Thru Metal Detector. (One or more can be send at the same time ! )

1.7- “?” signs for all windows are for help MENU.

1.8- “SEND” button resets old data and memorise the new assigned data to your ThruScan

s3/s6/s9

1.9- “Refresh” button reports the data of your ThruScan s3/s6/s9 in every 30secs to your PC. You could get data

instantly every second by pressing “Refresh” button. “Send” is not possible in Refresh Mode.

1.10- “Factory Settings” button enables to return to default settings. These settings can be re memorised by “SEND”

button. Counter values do not change at this process.

1.11- “X” button is for to quit from your SRC-SCADA Remote Control Programmer. This will shut down the

communication/telephone line also.

The author reserve the rights and disclaims all warranties as to this software, whether express or implied, including without limitation any implied warranties of

merchantability or fitness for a particular purpose. Use under your own responsibility, but comments (even critique) in English, German (or in Turkish) are welcome.

1 2 ... 48 49 50 51 52 53 54 55 56 57

Comentarios a estos manuales

Sin comentarios

Elektral ThruScan Manual de usuario Pagina 53

Comentarios a estos manuales